Group: Hardware/Computers/Single Board Computers/Plug Computers

From LibrePlanet
Jump to: navigation, search
Line 23: Line 23:
 
** WiFi and bluetooth both need a non-free loaded firmware, but the USB ports make it possible to use external WiFi and/or bluetooth dongles that can work with free software (both USB2 ports can provide up to 500mA)
 
** WiFi and bluetooth both need a non-free loaded firmware, but the USB ports make it possible to use external WiFi and/or bluetooth dongles that can work with free software (both USB2 ports can provide up to 500mA)
  
== Hardware features comparison ==
+
== Free software-compatible hardware features comparison ==
 +
 
 +
This table compares plug computers hardware features that work with free software. Hence, it does not mention hardware that requires non-free software to function.
  
 
{| class="wikitable"  border="1"
 
{| class="wikitable"  border="1"
Line 62: Line 64:
 
| N/A
 
| N/A
 
| 2x10/100/1000
 
| 2x10/100/1000
| 802.11 b/g/n, AP
+
| {{no}}
| 3.0
+
| {{no}}
 
|}
 
|}
  

Revision as of 07:17, 15 August 2013

Plug Computers are computers that fit in a small form-factor, are power-efficient and do not interact with the user directly through I/O devices such as monitor and keyboard, but are rather controlled remotely. Most of the time, Plug Computers use a System-on-a-Chip (SoC) with an ARM processor, run a GNU/Linux system and are used as domestic servers.

Software freedom comparison

While some Plug Computers can be used with fully free software running on the main processor, not all of them are perfect. Hence, here is a comparison of different models of Plug Computers and their flaws regarding software freedom.

Flawless targets

These plug computers can be operated with all the hardware features available, using only free software.

  • The Globalscale SheevaPlug can be operated using only free software:
    • The bootloader is free software and can easily be replaced
    • The kernel and all the drivers needed are free software
    • There is no hardware component that requires a non-free loaded firmware

Seriously flawed targets

These plug computers are usable with free software, but important hardware features are not functional. There may be workarounds for these however.

  • The Globalscale DreamPlug is flawed as the WiFi and bluetooth hardware require non-free firmwares
    • The bootloader is free software and can easily be replaced
    • The kernel and all the drivers needed are free software
    • WiFi and bluetooth both need a non-free loaded firmware, but the USB ports make it possible to use external WiFi and/or bluetooth dongles that can work with free software (both USB2 ports can provide up to 500mA)

Free software-compatible hardware features comparison

This table compares plug computers hardware features that work with free software. Hence, it does not mention hardware that requires non-free software to function.

Name Manufacturer SoC CPU frequency RAM Internal storage External storage USB PCI Ethernet WiFi Bluetooth
SheevaPlug Globalscale Kirkwood 88F6281 1.2 Ghz 512 Mb 512 Mb SD card 1xUSB2 N/A 1x10/100/1000 N/A N/A
DreamPlug Globalscale Kirkwood 88F6281 1.2 Ghz 512 Mb 4 Gb (µSD card) e-SATA, SD card 2xUSB2 N/A 2x10/100/1000 No No

Software features comparison

Currently, the best way to run fully free software on these plug computers is to use Debian with the matching ARM architecture. However, the situation with Debian is not good enough[1] for freedom, since Debian hosts a repository of non-free software and encourages their use through the packages web interface and the Debian wiki. Hence, it does not meet the requirements for Free System Distributions[2].

The FreedomBox software[3] is based upon Debian and comes with the same issues as Debian, mentioned above.

Name Manufacturer Architecture Bootloader Kernel GNU/Linux
SheevaPlug Globalscale ARMv5/armel Upstream U-Boot support Upstream Linux support Official Debian support
Dreamplug Globalscale ARMv5/armel Upstream U-Boot support Upstream Linux support Official Debian support