Group:Hardware/Computers/e-readers/Kobo/Aura H2O Edition 2/boot dmesg 01

[root@(none) ~]# dmesg 
Booting Linux on physical CPU 0x0
Linux version 4.1.15-00104-gcd6a6a6 (gallen@gallen-M51AC) (gcc version 5.3.0 (GCC) ) #9 SMP PREEMPT Wed Nov 15 15:40:03 CST 2017
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Freescale i.MX6SLL NTX Board
Memory policy: Data cache writeback
On node 0 totalpages: 130304
free_area_init_node: node 0, pgdat 807ce380, node_mem_map 9f7f7000
  Normal zone: 1016 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 130048 pages, LIFO batch:31
  HighMem zone: 256 pages, LIFO batch:0
CPU: All CPU(s) started in SVC mode.
PERCPU: Embedded 12 pages/cpu @9f7d2000 s16908 r8192 d24052 u49152
pcpu-alloc: s16908 r8192 d24052 u49152 alloc=12*4096
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129288
Kernel command line: console=ttymxc0,115200 rootwait rw no_console_suspend hwcfg_p=0x9ffffe00 hwcfg_sz=110 waveform_p=0x9fdc8a00 waveform_sz=2323160 ntxfw_p=0x9fdc6400 ntxfw_sz=9474 mem=509M boot_port=0 rootfstype=ext4 root=/dev/mmcblk0p1 quiet
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 508144K/521216K available (5303K kernel code, 221K rwdata, 2068K rodata, 368K init, 379K bss, 13072K reserved, 0K cma-reserved, 1024K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xa0000000 - 0xff000000   (1520 MB)
    lowmem  : 0x80000000 - 0x9fd00000   ( 509 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .text : 0x80008000 - 0x8073b01c   (7373 kB)
      .init : 0x8073c000 - 0x80798000   ( 368 kB)
      .data : 0x80798000 - 0x807cf460   ( 222 kB)
       .bss : 0x807d2000 - 0x80830d4c   ( 380 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
	Additional per-CPU info printed with stalls.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
NR_IRQS:16 nr_irqs:16 16
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 16 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 256 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76430001
mxc_clocksource_init 3000000
Switching to timer-based delay loop, resolution 333ns
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80008280 - 0x800082d8
Brought up 1 CPUs
SMP: Total of 1 processors activated (6.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
device-tree: Duplicate name in lcdif@020f8000, renamed to "display#1"
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
20ca000.usbphy supply phy-3p0 not found, using dummy regulator
ntx_parse_cmdline():cp cmdline=console=ttymxc0,115200 rootwait rw no_console_suspend hwcfg_p=0x9ffffe00 hwcfg_sz=110 waveform_p=0x9fdc8a00 waveform_sz=2323160 ntxfw_p=0x9fdc6400 ntxfw_sz=9474 mem=509M boot_port=0 rootfstype=ext4 root=/dev/mmcblk0p1 quiet
hwcfg_size_setup() hwcfg_szie=110
***_MemoryRequest:46: request memory region! addr=9ffffe00, len=110***
hwcfg_p_setup() hwcfg_p=9ffffe00,vaddr=a007ce00,size=110,pcb=0x3c
boot_port_setup() boot_port=0
ntxfw_size_setup() ntxfw_size=9474
***_MemoryRequest:46: request memory region! addr=9fdc6400, len=9474***
ntxfw[0],"E60QM2_dualfl_hdr_161116",type=0x6,sz=16
lm3630fl dual color table : 11 temperatures ,c1_pwr=0xa,c2_pwr=0x5
ntxfw[1],"E60QM2_dualfl_tab_161116",type=0x7,sz=9284
ntxfw_p_setup() ntxfw_p=9fdc6400,vaddr=a00b8400,size=9474,name="E60QM2",items=2
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6sll-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
PMU: ricoh61x_i2c_init:
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-0: can't use DMA
tps6518x_probe calling
tps6518x_i2c_parse_dt_pdata():gpio_pmic_pwrall=46
tps6518x_i2c_parse_dt_pdata():gpio_pmic_pwrall init set 1
tps6518x_i2c_parse_dt_pdata():gpio_pmic_wakeup=39
tps6518x_i2c_parse_dt_pdata():gpio_pmic_wakeup init set 1
tps6518x_i2c_parse_dt_pdata():gpio_pmic_powerup=40
tps6518x_detect calling
tps6518x_detect():revId=0x65
tps6518x_detect success
tps6518x 1-0068: PMIC TPS6518x for eInk display
tps6518x_probe success
i2c i2c-1: IMX I2C adapter registered
i2c i2c-1: can't use DMA
PMU: ricoh61x_i2c_probe:
ricoh61x_pre_init,line=941
ricoh61x irq gpio 115
invalid sleep gpio: -2
invalid dc_det gpio: -2
ricoh61x chg gpio 116
ricoh61x bat_low gpio 92
PMU: ricoh61x_irq_init: g_full_flag: 0, CHGSTS1: 0x00
ricoh61x_irq_init: ricoh619_pmic_irq=1
i2c i2c-2: IMX I2C adapter registered
i2c i2c-2: can't use DMA
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
PMU: ricoh61x_regulator_init
PMU: ricoh61x_regulator_probe
RICOH619_DC1 at 900000uv suspend
RICOH619_DC2 at 3300000uv suspend
RICOH619_DC3 at 1140000uv suspend
RICOH619_DC4 at 1140000uv suspend
RICOH619_DC5 at 1700000uv suspend
RICOH619_LDO2 at 3000000uv suspend
tps6518x-pmic tps6518x-pmic: request vcom gpio failed (-16)!
tps6518x-pmic tps6518x-pmic: request powerup gpio failed (-16)!
tps6518x_regulator_probe(1090): revID=101,6518x@9c147d00 wakeup gpio39=1
_tps6518x_vcom_get_voltage() : vcom=-2160000uV
_tps6518x_vcom_get_voltage() : vcom=-2160000uV
tps6518x_get_temperature():temperature = 25
tps6518x_get_temperature():temperature = 25
PMU RTC: ricoh61x_rtc_probe, ricoh61x driver run at 24H-mode
PMU RTC: we never using periodic function and interrupt
ricoh61x_rtc_Pon_get_clr, PON=1 -- CTRL2=0x20
PMU: ricoh61x_rtc_alarm_enable :0
PMU: ricoh61x_rtc_probe register rtc device
PMU: ricoh61x_rtc_read_alarm
rtc_ricoh619 rtc_ricoh619: PMU: read alarm: 6/18/2018 23:17:0 *****
rtc_ricoh619 rtc_ricoh619: rtc core: registered rtc_ricoh619 as rtc0
[ricoh61x_irq_sync_unlock-280] set 0xAE to 0x60
PMU: ricoh61x_rtc_alarm_enable :0
RICOH61x RTC Register Success
Switched to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1ls

imx rpmsg driver is registered.
Bus freq driver module loaded
futex hash table entries: 256 (order: 2, 16384 bytes)
bounce: pool size: 64 pages
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
lm3630a_bl_parse_dt pchip=9c1bf9d0,hwen_gpio 42
lm3630a_bl 0-0036: LM3630A[1] backlight register OK.
imx-sdma 20ec000.sdma: no event needs to be remapped
imx-sdma 20ec000.sdma: loaded firmware 3.3
imx-sdma 20ec000.sdma: initialized
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 18, base_baud = 5000000) is a IMX
console [ttymxc0] enabled
imx-rng 21b4000.rngb: iMX RNG Registered.
imx sema4 driver is registered.
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-mxc: Freescale On-Chip EHCI Host driver
usbcore: registered new interface driver usb-storage
2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
2184000.usb supply vbus not found, using dummy regulator
mousedev: PS/2 mouse device common for all mice
input: ntx_event0 as /devices/platform/ntx_event0/input/input0
set cyttsp5 touch flags by dts=0x4
set cyttsp5 touch flags by hwconfig=0x30
cyttsp5_i2c_adapter 1-0024: cyttsp5_init: INIT CYTTSP RST gpio=114 and IRQ gpio=120 r=0
cyttsp5_i2c_adapter 1-0024: cyttsp5_startup_: Bootloader mode
cyttsp5_i2c_adapter 1-0024: cyttsp5_startup_: Operational mode
cyttsp5_i2c_adapter 1-0024: cyttsp5_startup_: Reading report descriptor
cyttsp5_i2c_adapter 1-0024: cyttsp5 Protocol Version: 1.6
input: cyttsp5_mt as /devices/platform/soc/2100000.aips-bus/21a4000.i2c/i2c-1/1-0024/input/input1
cyttsp5_i2c_adapter 1-0024: cyttsp5_loader_probe: Successful probe 1-0024
cyttsp5_loader_init: Parade TTSP FW Loader Driver (Built TTDA.03.07.844339) rc=0
snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
i2c /dev entries driver
syscon-poweroff 20cc000.snvs:snvs-poweroff: pm_power_off already claimed 80021518 ntx_machine_poweroff
syscon-poweroff: probe of 20cc000.snvs:snvs-poweroff failed with error -16
PMU: ricoh61x_battery_init
PMU: ricoh61x_battery_probe : version is RICOH61x_BATTERY_VERSION: 2014.02.21 V3.1.0.0-Solution1 2015/02/09
ricoh619_battery_dt_init type_n=0
ricoh61x_battery_probe type_n=0,temp is 1
ricoh61x_battery_probe info->num=0,temp is 4
PMU FG_RESET : ricoh61x_init_battery : initial pswr = 100
PMU : ricoh61x_init_battery : POWER off history 0x0a is 0x10 
PMU : ricoh61x_init_battery : POWER control function 0x0d is 0x00 
PMU : ricoh61x_init_battery : off is 424819, on is 424819, period is 0, fpon_flag is 0
PMU: ricoh61x_set_OCV_table : 00% voltage = 3579900 uV
PMU: ricoh61x_set_OCV_table : 10% voltage = 3687400 uV
PMU: ricoh61x_set_OCV_table : 20% voltage = 3743500 uV
PMU: ricoh61x_set_OCV_table : 30% voltage = 3768000 uV
PMU: ricoh61x_set_OCV_table : 40% voltage = 3788700 uV
PMU: ricoh61x_set_OCV_table : 50% voltage = 3818000 uV
PMU: ricoh61x_set_OCV_table : 60% voltage = 3879100 uV
PMU: ricoh61x_set_OCV_table : 70% voltage = 3941300 uV
PMU: ricoh61x_set_OCV_table : 80% voltage = 4004800 uV
PMU: ricoh61x_set_OCV_table : 90% voltage = 4083000 uV
PMU: ricoh61x_set_OCV_table : 100% voltage = 4183100 uV
PMU : ricoh61x_set_OCV_table : target_vsys is 3012 target_ibat is 302
PMU : ricoh61x_scaling_OCV_table : setting value of cuttoff_vol(3092) is out of range(3579900) 
PMU : ricoh61x_scaling_OCV_table : new table
PMU : ricoh61x_scaling_OCV_table : ocv_table 0 is 35788 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 1 is 36850 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 2 is 37411 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 3 is 37668 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 4 is 37875 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 5 is 38168 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 6 is 38779 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 7 is 39389 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 8 is 40037 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 9 is 40818 v
PMU : ricoh61x_scaling_OCV_table : ocv_table 10 is 41819 v
PMU : ricoh61x_init_charger : GCHGDET (0xDA) is 0x78
PMU : ricoh61x_init_charger : after CHGISET_REG (0xb8) is 0x44 info->ch_ichg is 0xff info->ch_icchg is 0x1
PMU : ricoh61x_init_charger : before BATSET1_REG (0xba) is 0x49 info->ch_vbatovset is 0xff
PMU : ricoh61x_init_charger : after BATSET1_REG (0xba) is 0x49 info->ch_vbatovset is 0xff
PMU : ricoh61x_init_charger : before BATSET2_REG (0xbb) is 0x33 info->ch_vrchg is 0xff info->ch_vfchg is 0xff 
PMU : ricoh61x_init_charger : test test val 48, val2 3 vfchg 4200
PMU : ricoh61x_init_charger : test test val 64, val2 1 icchg 100
PMU : ricoh61x_init_charger : 100 min 4115000, 100 max 4239000 vfchg 4200 icchg 100 rbat 211
PMU: ricoh61x_init_fgsoca : * 00% voltage = 3578700 uV
PMU: ricoh61x_init_fgsoca : * 10% voltage = 3684900 uV
PMU: ricoh61x_init_fgsoca : * 20% voltage = 3741100 uV
PMU: ricoh61x_init_fgsoca : * 30% voltage = 3766700 uV
PMU: ricoh61x_init_fgsoca : * 40% voltage = 3787500 uV
PMU: ricoh61x_init_fgsoca : * 50% voltage = 3816800 uV
PMU: ricoh61x_init_fgsoca : * 60% voltage = 3877800 uV
PMU: ricoh61x_init_fgsoca : * 70% voltage = 3938900 uV
PMU: ricoh61x_init_fgsoca : * 80% voltage = 4003600 uV
PMU: ricoh61x_init_fgsoca : * 90% voltage = 4081800 uV
PMU: ricoh61x_init_fgsoca : * 100% voltage = 4181900 uV
calc_soc_by_voltageMethod(): FG not ready , getting vbatt from ADC .
measure_vbatt_ADC():4195000 uV
PMU: ricoh61x_init_fgsoca : * Rbat = 211 mOhm   n_cap = 1510 mAH
Create pmic_battery.1 in platform
tps6518x_sensor_probe starting
tps6518x_sensor_probe success
imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
/soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified
sdhci-esdhc-imx 2190000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
led_classdev_register():led_cdev->name=mmc0::,name=mmc0::
mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
led_classdev_register():led_cdev->name=mmc1::,name=mmc1::
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
/soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified
sdhci-esdhc-imx 2198000.usdhc: assigned as wifi host
sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found
led_classdev_register():led_cdev->name=mmc2::,name=mmc2::
mmc0: MAN_BKOPS_EN bit is not set
mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
led_classdev_register():led_cdev->name=GLED,name=GLED
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
mmc0: new DDR MMC card at address 0001
mmcblk0: mmc0:0001 8GME4R 7.28 GiB 
mmcblk0boot0: mmc0:0001 8GME4R partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 8GME4R partition 2 4.00 MiB
mmcblk0rpmb: mmc0:0001 8GME4R partition 3 512 KiB
cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
 mmcblk0: p1 p2 p3
ntx_wifi_power_ctrl(0) called
drivers/video/fbdev/mxc/mxc_epdc_v2_fb.c(6711):EPD 1440x1080 
imx_epdc_v2_fb 20f4000.epdc: resolution 1440x1080, bpp 16
imx_epdc_v2_fb 20f4000.epdc: EPDC version = 30
_tps6518x_vcom_get_voltage() : vcom=-2160000uV
waveform_size_setup() wf_size=2323160
***_MemoryRequest:171: request memory region! addr=0x9fdc8a00, len=2323160***
waveform_p_setup() wf_p=9fdc8a00,vaddr=a1c00a00,size=2323160
mxc_epdc_fb_init_hw(6486)
[epdc_firmware_work_func]:fw p=a1c00a00,size=2323160,fb_data@9c026000,pdata=807addd8
mxc_epdc_fb_fw_handler(6008),fw=9c187ee8
mxc_epdc_fb_fw_handler(): fw p=a1c00a00,size=2323160
imx_epdc_v2_fb 20f4000.epdc:  --- Extra Waveform Data length: 29 bytes---
imx_epdc_v2_fb 20f4000.epdc:      Extra Waveform Data: 320_R208_AF2021_ED068TH1U4_TC
_get_fp9928():"/soc/aips-bus@02100000/i2c@021a4000/fp9928@48" device node not found !!
fake_s1d13522_parse_epd_cmdline : epd cmdline parse already done .
drivers/video/fbdev/mxc/mxc_epdc_fake_s1d13522.c(1495):k_fake_s1d13522_init,DisplayResolution=3
imx_epdc_v2_fb 20f4000.epdc: Unable to get an accurate EPDC pix clkdesired = 96000000, actual = 80000000
Power:do-not-wakeup-hibernation=0
Hall:do-not-wakeup-hibernation=0
drivers/video/fbdev/mxc/mxc_epdc_v2_fb.c,epdc_init_settings():epdc_mode="ED068OG1_NUMCE3"
imx_epdc_v2_fb 20f4000.epdc: 16bits mirror display bus width 
rtc_ricoh619 rtc_ricoh619: setting system clock to 2018-06-18 19:28:45 UTC (1529350125)
TMST: disabling
RICOH619_LDORTC2: disabling
RICOH619_LDORTC1: disabling
RICOH619_LDO10: disabling
RICOH619_LDO9: disabling
RICOH619_LDO4: disabling
ALSA device list:
  No soundcards found.
EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:1.
devtmpfs: mounted
Freeing unused kernel memory: 368K (8073c000 - 80798000)
_tps6518x_vcom_get_voltage() : vcom=-2160000uV
tps6518x_get_temperature():temperature = 25
EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
udevd (93): /proc/93/oom_adj is deprecated, please use /proc/93/oom_score_adj instead.
PMU:check_charging_state_work --- Battery exist !! Return Normal mode ---0x44
PMU: ricoh61x_displayed_work : dsoc_temp(10000), soc(10000), cc_delta(97)
PMU: ricoh61x_displayed_work : status(0), rsoc_ready_flag(0)
PMU FG_RESET : ricoh61x_displayed_work : initial  dsoc  is  10000
PMU: ricoh61x_displayed_work Half-Clear CC, init_pswr(100), cc_delta(97)
PMU:STATUS= 3: IBAT= -3: VSYS= 4426000: VBAT= 4195300: DSOC= 10000: RSOC= 10000: cc_delta=97: rrf= 0
FAT-fs (mmcblk0p3): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
random: dbus-uuidgen urandom read with 59 bits of entropy available
PMU: ricoh61x_rtc_alarm_enable :0
usb plugged 257
[_lm3630a_set_FL-1014] led A c=0,b=0, led B c=0,b=0
_tps6518x_vcom_get_voltage() : vcom=-2160000uV
ntx_power_key_hook():state=0
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
lit_ctl
command exec successfully!
cyttsp5_i2c_adapter 1-0024: cyttsp5_core_rt_resume: Error on wake
imx_epdc_v2_fb 20f4000.epdc: mxc_epdc_fb_set_pwrdown_delay(),pwrdwn_delay=100 
_tps6518x_vcom_get_voltage() : vcom=-2160000uV
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=50
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=67
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=78
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=87
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=95
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=104
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=111
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=118
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=124
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=130
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=134
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=138
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=141
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=144
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=146
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=149
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=151
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=153
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=155
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=157
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=159
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=162
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=164
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=167
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=169
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=171
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=177
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=179
random: nonblocking pool is initialized
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=181
[_lm3630a_set_FL-1014] led A c=10,b=0, led B c=5,b=182
PMU: ricoh61x_rtc_set_alarm
PMU: ricoh61x_rtc_alarm_enable :0
ricoh619 2-0032: PMU: print_time *** rtc-time : 6/18/2018 23:12:46 *****
PMU: ricoh61x_rtc_alarm_enable :1
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
dualcolor[10][30] curr=10790
PM: suspend of devices complete after 99.821 msecs
PM: suspend devices took 0.110 seconds
PM: late suspend of devices complete after 3.736 msecs
PM: noirq suspend of devices complete after 1.855 msecs
Disabling non-boot CPUs ...
Turn off M/F mix!
PM: noirq resume of devices complete after 0.780 msecs
imx-sdma 20ec000.sdma: loaded firmware 3.3
wait 3ms for 65185 wake up 
PM: early resume of devices complete after 6.376 msecs
drivers/video/fbdev/mxc/mxc_epdc_v2_fb.c,epdc_init_settings():epdc_mode="ED068OG1_NUMCE3"
imx_epdc_v2_fb 20f4000.epdc: 16bits mirror display bus width 
ntx_power_key_hook():state=0
PM: resume of devices complete after 208.096 msecs
PM: resume devices took 0.210 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
PMU: ricoh61x_rtc_alarm_enable :0
PMU: ricoh61x_displayed_work Half-Clear CC, init_pswr(100), cc_delta(0)
PMU:STATUS= 6: IBAT= -4: VSYS= 4406000: VBAT= 4195300: DSOC= 10000: RSOC= 10000: cc_delta=0: rrf= 0
PMU: ricoh61x_rtc_set_alarm
PMU: ricoh61x_rtc_alarm_enable :0
ricoh619 2-0032: PMU: print_time *** rtc-time : 6/18/2018 23:12:46 *****
PMU: ricoh61x_rtc_alarm_enable :1
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
dualcolor[10][30] curr=10790
PM: suspend of devices complete after 91.408 msecs
PM: suspend devices took 0.090 seconds
PM: late suspend of devices complete after 3.685 msecs
PM: noirq suspend of devices complete after 1.860 msecs
Disabling non-boot CPUs ...
Turn off M/F mix!
PM: noirq resume of devices complete after 0.776 msecs
imx-sdma 20ec000.sdma: loaded firmware 3.3
wait 3ms for 65185 wake up 
PM: early resume of devices complete after 5.993 msecs
drivers/video/fbdev/mxc/mxc_epdc_v2_fb.c,epdc_init_settings():epdc_mode="ED068OG1_NUMCE3"
imx_epdc_v2_fb 20f4000.epdc: 16bits mirror display bus width 
ntx_power_key_hook():state=0
PM: resume of devices complete after 202.763 msecs
PM: resume devices took 0.210 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
PMU: ricoh61x_rtc_alarm_enable :0
PMU: ricoh61x_displayed_work Half-Clear CC, init_pswr(99), cc_delta(99)
PMU:STATUS= 6: IBAT= -4: VSYS= 4410000: VBAT= 4196500: DSOC= 10000: RSOC= 9900: cc_delta=99: rrf= 0
PMU: ricoh61x_rtc_set_alarm
PMU: ricoh61x_rtc_alarm_enable :0
ricoh619 2-0032: PMU: print_time *** rtc-time : 6/18/2018 23:12:46 *****
PMU: ricoh61x_rtc_alarm_enable :1
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Entering mem sleep
dualcolor[10][30] curr=10790
PM: suspend of devices complete after 89.385 msecs
PM: suspend devices took 0.090 seconds
PM: late suspend of devices complete after 3.715 msecs
PM: noirq suspend of devices complete after 1.842 msecs
Disabling non-boot CPUs ...
Turn off M/F mix!
PM: noirq resume of devices complete after 0.777 msecs
imx-sdma 20ec000.sdma: loaded firmware 3.3
wait 3ms for 65185 wake up 
PM: early resume of devices complete after 5.990 msecs
drivers/video/fbdev/mxc/mxc_epdc_v2_fb.c,epdc_init_settings():epdc_mode="ED068OG1_NUMCE3"
imx_epdc_v2_fb 20f4000.epdc: 16bits mirror display bus width 
ntx_power_key_hook():state=0
PM: resume of devices complete after 202.570 msecs
PM: resume devices took 0.210 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
PMU: ricoh61x_rtc_alarm_enable :0
PMU: ricoh61x_displayed_work Half-Clear CC, init_pswr(99), cc_delta(98)
PMU:STATUS= 6: IBAT= -4: VSYS= 4406000: VBAT= 4194100: DSOC= 10000: RSOC= 9900: cc_delta=98: rrf= 0